Simuair software free download

Transcription

1 SIMULATION SOFTWARE FOR HVACR TRAINING Simulator Training Systems

2 TABLE OF CONTENTS General Information Instructor Interfaces Air Conditioner Simulator SIMUAIR for Windows Heat Pump Simulator SIMUPUMP for Windows Commercial Refrigeration Simulator SIMUREFR for Windows Supermarket Refrigeration Simulator SIMUMKT for Windows Gas Furnace Simulator SIMUGAS for Windows Oil Furnace Simulator SIMUOIL for Windows Hot Water Boiler Simulator SIMUHYDRO for Windows Ordering Information Price list for multiple-licenses Simutech the leader in hands-on HVAC/R service training software offers a wide array of computer-based simulators for Heating, Ventilation, Air Conditioning, and Refrigeration. Simutech simulators use animated graphics and sophisticated computer-modeling to emulate faults in HVACR systems. The simulators allow the trainee to measure various mechanical and electrical values to determine the cause of the fault, then perform repairs to return the system to normal operation. Computer simulation has been proven to be the ideal method of training students and technicians in the servicing of HVACR equipment. A trainee can quickly learn operating characteristics, and proper troubleshooting and repair methods for faults commonly encountered during service calls. Simulators are also useful when studying for technician certification exams, including NATE and ICE. All levels of users from the entry-level student to the most seasoned technician will greatly benefit by using Simutech hands-on simulators. That s why our simulators are used extensively by vocational schools, colleges, trade unions, correctional institutions, contractors, and facilities, worldwide! The simulators are easy to use, even for novice computer users! Instructors quickly discover that Simutech simulators are invaluable tools in teaching HVACR troubleshooting and theory-of-operation. Prior to their hands-on exposure to the real equipment, students learn proper troubleshooting and repair methods, refrigerant handling, safety practices, and use of test equipment. Plus, simulators provide training at a fraction of the cost of purchasing and maintaining mechanical HVACR equipment and facilities! Besides the cost factor, computer-based training has been proven to greatly enhance the retention level and interest of students! Simutech simulators meet the accreditation standards of PAHRA and HVAC Excellence. Service technicians can use the simulators to improve their troubleshooting skills, or cross-train on different types of equipment. Training can be scheduled at any time, and with minimal supervision. Simulators are a great alternative to costly and time-consuming training seminars! 2015 Simutech Systems, Inc Printed in U.S.A. IBM PC is a registered trademark of IBM Corp. Pentium and Core are registered trademarks of Intel Corp. Windows XP, Vista, 7, 8, 8.1, 10, NT, 2000, Server 2003, Server 2008, and Server 2012 are registered trademarks of Microsoft Corp. Employers find Simutech simulators to be useful in testing and evaluating technicians during the hiring process. Poorly skilled technicians or part swappers are easily identified, simply by reviewing the repair logs and other reports that are automatically generated by the software. You ll find Simutech simulators are easy to use, even for novice computer users! The software runs on any Windows based PC and no Internet connection is required.

3 GENERAL INFORMATION REALISTIC SIMULATION Simutech training simulators are designed to represent generic HVACR systems that a service technician would commonly encounter in the field. Extremely accurate and realistic pressures, temperatures, and electrical values are maintained during the system s operation, under both normal and fault conditions. FAULT INSERTION Up to 40 commonly encountered mechanical and electrical faults may be preselected by the instructor or randomly selected by the computer. Once a fault is inserted, the simulator will operate according to predetermined fault conditions. INSTRUCTOR REPORTS To monitor the performance of each trainee, Activity Reports, Fault Status Reports, Instrument Logs, and Repair Logs are generated for the instructor. Each user s log-on time, troubleshooting time, fault insertions, instrument usage, and repair attempts are tracked and permanently stored in the database. The Repair Log lists all repairs and parts replacements made by a user during a fault insertion. This provides the instructor an excellent means of evaluating the users troubleshooting skills. INSTRUMENTATION Realistic and accurate instrument readings can be taken at numerous locations throughout the simulated system. These readings correspond to the simulator s current operating state and fault condition. They include pressure, temperature, voltage, current, resistance, and combustion components. DIAGNOSTIC CHARTS After taking readings with the test instruments, the trainee can refer to on-screen diagnostic charts to isolate the faulty component and repair the system. On-screen test procedures provide proper industry-standard methods to check a suspect component, and provide typical instrument readings. EXTENSIVE HELP MENUS & MANUALS Context-sensitive help menus guide the trainee and instructor at every step and command. Even a computer-novice can easily use Simutech simulators! In addition, both a comprehensive printed User s Manual and Instructor s Manual are included. NETWORKABLE The simulators may be installed on most local-area network (LAN) servers. The network versions must be purchased for the maximum users that will be logged-on simultaneously. MULTI-USER CAPABILITY Up to 99 users can be assigned per stand-alone computer or network. Repair logs, fault selections, and other data is saved for each user on the hard drive of each workstation or server. INSTRUCTOR INTERFACES These optional programs are installed on the instructor s computer to enable him to preselect faults for all users, at one time. Using a disk or flash drive, the faults are then easily uploaded to each workstation. In addition, when a printer isn t available at each workstation, these interfaces can be used to download the reports, for display and printout at the instructor s computer. These interfaces are recommended when six or more workstations are utilized without a network. 1

4 AIR CONDITIONER SIMULATOR SIMUAIR SIMUAIR simulates two generic versions of residential and light-commercial air conditioning systems, using either R-22 or R-410A refrigerant. These systems include a packaged unit with a capillary tube and PSC motor circuit, and a split-system with a thermostatic expansion valve and CSR motor circuit. Animated mechanical and electrical schematic diagrams of the simulated system are provided in real-time. The mechanical diagram shows refrigerant flow, as well as the liquid, vapor, liquid/vapor, and superheated vapor states of the refrigerant. In the electrical ladder diagram, the controls and switch contacts constantly change state as the system operates. Providing a means of visually tracing refrigerant and current flow during operation, makes it much easier for the trainee to understand how an air conditioner is supposed to work. The trainee can zoom into the system to visually inspect various components, including dirt or ice on coils, and a dirty air filter. He can also listen to the compressor running. SIMUAIR provides easy-to-use point-and-click selection of meters and test points, and are saved to an Instrument Log to monitor the users troubleshooting skill. Temperatures may be displayed in either Fahrenheit ( F) or Celsius ( C), and pressures may be displayed in either imperial (psig) or metric Indoor and ambient temperatures, and relative humidity are adjustable and continuously updated and displayed on the screen. Settings for thermostat setpoint, limit switches, TXV, circuit breakers, and other controls may be changed by the trainee. With the capability of changing operating temperatures and relative humidity, a system may be observed under various environmental conditions; something very difficult to do with real mechanical equipment. Pressure-temperature charts, performance charts, specifications, and an electrical nomenclature, are available on-screen. 2

5 AIR CONDITIONER SIMULATOR SIMUAIR SYSTEM REQUIREMENTS SIMUAIR for Windows requires the following minimum IBM compatible PC computer: Pentium, Core, or equivalent processor (32 or 64-bit) Windows XP, Vista, 7, 8, 8.1, or 10 VGA/SVGA display Hard drive, 18MB available disk space SIMUAIR network version is compatible with Novell and Windows 2000, Server 2003, Server 2008, and Server 2012 (kpa/barg). The on-screen test instruments include: Gauge manifold set Voltmeter Thermometers Ohmmeter Leak detector Clamp-on ammeter Up to 20 commonly encountered mechanical and electrical faults may be selected, as shown in the Fault List above. FREE DEMO DISK (800) SIMUAIR provides testing and troubleshooting of the devices listed below, which are commonly found in air conditioners. Compressor Condenser coil Evaporator coil TX valve (TXV/TEV) Capillary tube Filter-drier Air filter Outdoor fan motor Indoor fan motor Transformer Contactor Start relay Indoor fan relay Crankcase heater Compressor run capacitor Compressor start capacitor Fan motor capacitor Room thermostat Low pressure switch High pressure switch Fan switch Circuit breaker ORDERING INFORMATION SIMUAIR Air Conditioner Simulator Version 5.6 MA-500 Stand-alone computer version, single license $ MA-560 Network version, 25-user (seat) license $1, MA-570 Network version, 50-user (seat) license $2, TA-500 ACINST Instructor Interface, Version 5.1 $ For further prices and ordering information, please see Page 16 3

6 HEAT PUMP SIMULATOR SIMUPUMP SIMUPUMP simulates a generic residential/light-commercial type air-to-air split-system heat pump, using either R-22 or R-410A refrigerant. The trainee may select heating, cooling, or emergency heat modes. Indoor and outdoor temperatures are adjustable, and continuously updated and displayed on the screen. Settings for thermostats, TXVs, defrost frequency, and building heatloss are also adjustable. With the capability of changing operating temperatures, a heat pump may be observed under various environmental conditions; something very difficult to do with real mechanical equipment. SIMUPUMP provides easy-to-use point-and-click selection of meters and test points, and are saved to an Instrument Log to monitor the users troubleshooting skill. Temperatures may be displayed in either Fahrenheit ( F) or Celsius ( C), and pressures may be displayed in either imperial (psig) or metric (kpa/barg). The on-screen test instruments include: Gauge manifold set Voltmeter Thermometers Ohmmeter Leak detector Clamp-on ammeter Animated mechanical and electrical schematic diagrams of the simulated heat pump are provided in real-time. The mechanical diagram shows refrigerant flow, as well as the liquid, liquid/vapor, and superheated vapor states of the refrigerant. In the electrical ladder diagrams, the controls and switch contacts constantly change state as the system operates. Providing a means of visually tracing refrigerant and current flow during operation, makes it much easier for the trainee to understand how a heat pump is supposed to work. Pressure-temperature charts, performance charts, specifications, and an electrical nomenclature are available on-screen. In addition, the trainee can zoom into the system to visually inspect various components, including dirt or ice on the coils, a dirty air filter, and a blocked outdoor unit. 4

7 HEAT PUMP SIMULATOR SIMUPUMP SYSTEM REQUIREMENTS SIMUPUMP for Windows requires the following minimum IBM compatible PC computer: Pentium, Core, or equivalent processor (32 or 64-bit) Windows XP, Vista, 7, 8, 8.1, or 10 VGA/SVGA display Hard drive, 18MB available disk space Up to 40 commonly encountered mechanical and electrical faults may be selected, as shown in the Fault Lists above. SIMUPUMP provides testing and troubleshooting of the devices shown below, which are commonly found in heat pumps. SIMUPUMP network version is compatible with Novell and Windows 2000, Server 2003, Server 2008, and Server 2012 FREE DEMO DISK (800) Compressor Condenser coil Evaporator coil Accumulator TX valve (TXV/TEV) Check valve Filter-drier Air filter Outdoor fan Indoor fan Reversing valve Compressor contactor Indoor fan relay Defrost relay Heater relay Reversing valve solenoid Transformer Defrost timer Auxiliary heater element Crankcase heater Run capacitor Fan motor capacitor Room thermostat Heat thermostat Outdoor thermostat Defrost thermostat Emergency heat switch Fan switch Limit switch Fused link Circuit breaker ORDERING INFORMATION SIMUPUMP Heat Pump Simulator Version 5.4 MP-500 Stand-alone computer version, single license $ MP-560 Network version, 25-user (seat) license $1, MP-570 Network version, 50-user (seat) license $2, TP-500 HPINST Instructor Interface, Version 5.1 $ For further prices and ordering information, please see Page 16 5

8 COMMERCIAL REFRIGERATION SIMULATOR SIMUREFR SIMUREFR simulates three generic versions of low-temperature and medium-temperature refrigeration systems. These include a reach-in case with random defrost, a reach-in freezer with electric defrost, and a walk-in freezer with hot-gas defrost. The trainee may select the type of refrigerant for the simulated system. Box and ambient temperatures are adjustable and continuously updated and displayed on the screen. The cut-in and differential settings for the pressurestat, thermostat, and low-pressure switch are also adjustable, as well as the defrost and TXVsettings. Eight common refrigerants may be selected for the simulated system. These include: R-12 R-22 R-134a R-402A R-404A R-409A R-502 R-507 SIMUREFR provides easy-to-use point-and-click selection of meters and test points, and are saved to an Instrument Log to monitor the users troubleshooting skill. Temperatures may be Animated mechanical and electrical schematic diagrams of the simulated refrigeration system are provided in real-time. The mechanical diagrams show refrigerant flow, as well as the liquid, vapor, liquid/vapor, and superheated vapor states of the refrigerant. Also, the liquid level in the receiver is shown. In the electrical ladder diagrams, the controls and switch contacts constantly change state as the system operates. Providing a means of visually tracing the refrigerant and current flow during system operation, makes it much easier for the trainee to understand how a refrigeration system is supposed to work. Pressure-temperature charts, specifications, and an electrical nomenclature are available on-screen. In addition, the trainee can zoom into the system to visually inspect various components, including dirt or ice on coils, and bubbles in the liquid sight glass. 6

9 COMMERCIAL REFRIGERATION SIMULATOR SIMUREFR SYSTEM REQUIREMENTS SIMUREFR for Windows requires the following minimum IBM compatible PC computer: Pentium, Core, or equivalent processor (32 or 64-bit) Windows XP, Vista, 7, 8, 8.1, or 10 VGA/SVGA display Hard drive, 18MB available disk space displayed in either Fahrenheit ( F) or Celsius ( C), and pressures may be displayed in either imperial (psig) or metric (kpa/barg). The on-screen test instruments include: Gauge manifold set Voltmeter Thermometers Ohmmeter Leak detector Clamp-on ammeter Up to 30 commonly encountered mechanical and electrical faults may be selected, as shown in the Fault Lists above. SIMUREFR network version is compatible with Novell and Windows 2000, Server 2003, Server 2008, and Server 2012 FREE DEMO DISK (800) SIMUREFR provides testing and troubleshooting of the devices listed below, commonly found in refrigeration systems. Compressor Condenser coil Evaporator coil Receiver TX valve (TXV/TEV) CPR valve Filter-drier Sight glass Condenser fan motor Evaporator fan motor Start relay Liquid line solenoid Hot gas solenoid Run capacitor Start capacitor Defrost heater Defrost timer motor Defrost timer solenoid Defrost thermostat Box thermostat Box pressurestat Low pressure switch High pressure switch Heater limit switch Condenser fan switch Circuit breaker ORDERING INFORMATION SIMUREFR Commercial Refrigeration Simulator Version 5.3 MR-500 Stand-alone computer version, single license $ MR-560 Network version, 25-user (seat) license $1, MR-570 Network version, 50-user (seat) license $2, TR-500 REFRINST Instructor Interface, Version 5.1 $ For further prices and ordering information, please see Page 16 7

10 SUPERMARKET REFRIGERATION SIMULATOR SIMUMKT SIMUMKT simulates a typical parallel-type multi-evaporator supermarket refrigeration system. Normally, a parallel system contains many display cases and walk-in coolers, but for simplicity, SIMUMKT contains three display cases. One case is low-temperature with electric defrost, the others are mediumtemperature with off-cycle defrost. Two 3-phase semi-hermetic compressors, with capacity cycling, are included. A specific refrigerant may be selected for simulation, which includes R-22, R-402A, R-404A, R-422D, R-502, and R-507. Animated mechanical and electrical schematic diagrams of the simulated refrigeration system are provided in real-time. The mechanical diagrams show refrigerant flow and the liquid, vapor, liquid/vapor, and superheated vapor states of the refrigerant. Also, the liquid level in the receiver is shown. In the electrical ladder diagrams, the controls and switch contacts constantly change state as the system operates. Providing a means of visually tracing the refrigerant and current flow during system operation, makes it much easier for the trainee 8

11 SUPERMARKET REFRIGERATION SIMULATOR SIMUMKT Compressor Condenser coil Evaporator coil Liquid receiver Oil reservoir Oil separator Oil level regulator Oil level sight glass Filter-drier Liquid-line sight glass OPR valve IPR valve EPR valve TX valve (TXV/TEV) Compressor motor (3-phase) Condenser fan motor Evaporator fan motor Contactor Defrost timer unit Motor starter Defrost heater Defrost thermostat Compressor-cycling switch High-pressure switch Oil pressure switch Heater limit switch Control switch Circuit breaker SIMUMKT provides testing and troubleshooting of the devices listed above, commonly found in refrigeration systems. SYSTEM REQUIREMENTS SIMUMKT for Windows requires the following minimum IBM compatible PC computer: Pentium, Core, or equivalent processor (32 or 64-bit) Windows XP, Vista, 7, 8, 8.1, or 10 VGA/SVGA display Hard drive, 18MB available disk space to understand how the system is supposed to work. Up to 30 commonly encountered mechanical and electrical faults may be selected, as shown in the Fault Lists above. Setpoints for the EPR valves and TXVs can be adjusted for each case, as well as the compressor-cycling control and defrost settings. Case and ambient temperatures are adjustable, and continuously updated and displayed on the screen. All temperature and pressure values can be set and displayed in either imperial or metric. Pressure-temperature charts for the refrigerants, specifications, and an electrical nomenclature are available on-screen. In addition, the trainee can zoom into the system to visually inspect various components, including dirty or iced-up coils, and liquid and compressor oil level sight glasses. SIMUMKT provides easy-to-use point-and-click selection of meters and test points, which are saved to an Instrument Log to monitor the users troubleshooting skill. Temperatures may be displayed in either Fahrenheit ( F) or Celsius ( C), and pressures may be displayed in either imperial (psig) or metric (kpa/barg). The on-screen test instruments include: Gauge manifold set Voltmeter Thermometers Ohmmeter Leak detector Clamp-on ammeter SIMUMKT network version is compatible with Novell and Windows 2000, Server 2003, Server 2008, and Server 2012 FREE DEMO DISK (800) ORDERING INFORMATION SIMUMKT Supermarket Refrigeration Simulator Version 5.3 MS-500 Stand-alone computer version, single license $ MS-560 Network version, 25-user (seat) license $1, MS-570 Network version, 50-user (seat) license $2, TS-500 MKTINST Instructor Interface, Version 5.1 $ For further prices and ordering information, please see Page 16 9

12 GAS FURNACE SIMULATOR SIMUGAS SIMUGAS simulates two generic versions of gas furnaces. These include a high-efficiency condensing furnace with hotsurface ignition (HSI), and a standard-efficiency furnace with standing pilot ignition. Either natural gas or liquidpetroleum (LP) gas may be selected for simulation. Room and ambient temperatures, room thermostat, burner air-shutters, fan limit, high limit, heat anticipator, and manifold pressure are all adjustable. The room and ambient temperatures, in either Fahrenheit or Celsius, are constantly updated and displayed. Animated mechanical and electrical schematic diagrams of the simulated gas furnace are provided in real-time. The mechanical diagrams show the burner flames, gas flow, and blower rotation. In the electrical ladder diagrams, the controls and switch contacts constantly change state as the system operates. The trainee can zoom into the furnace to visually inspect various components, including checking for a dirty air filter or heat exchanger, and the position of the flame sensor. Typical types of burner flames are also shown. Up to 30 commonly 10

13 GAS FURNACE SIMULATOR SIMUGAS Primary heat exchanger Secondary heat exchanger Combustion chamber Manifold Burners Orifices Air filter Gas valve Vent pipe Draft hood Pilot burner Thermocouple Blower motor Vent blower motor Transformer Blower relay Heat relay Gas control valve Ignitor element Ignition module Gas control coil Flame sensor Run capacitor Room thermostat High limit switch Fan switch Vent pressure switch Rollout switch Door switch Circuit breaker SIMUGAS provides testing and troubleshooting of the devices listed above, which are commonly found in gas furnaces. SYSTEM REQUIREMENTS SIMUGAS for Windows requires the following minimum IBM compatible PC computer: Pentium, Core, or equivalent processor (32 or 64-bit) Windows XP, Vista, 7, 8, 8.1, or 10 VGA/SVGA display Hard drive, 17MB available disk space encountered mechanical and electrical faults may be selected, as shown in the Fault Lists above. SIMUGAS provides easy-to-use point-and-click selection of meters and test points, which are saved to an Instrument Log to monitor the users troubleshooting skill. Temperatures may be displayed in either Fahrenheit ( F) or Celsius ( C), and pressures may be displayed in either imperial (in. w.c.) or metric (kpa). The on-screen test instruments include: Manometer Millivoltmeter Thermometers Ohmmeter Combustion analyzer Clamp-on ammeter Ignition module tester Microammeter Voltmeter SIMUGAS network version is compatible with Novell and Windows 2000, Server 2003, Server 2008, and Server 2012 FREE DEMO DISK (800) ORDERING INFORMATION SIMUGAS Gas Furnace Simulator Version 5.2 MF-500 Stand-alone computer version, single license $ MF-560 Network version, 25-user (seat) license $1, MF-570 Network version, 50-user (seat) license $2, TF-500 GASINST Instructor Interface, Version 5.1 $ For further prices and ordering information, please see Page 16 11

14 OIL FURNACE SIMULATOR SIMUOIL SIMUOIL simulates four common configurations of generic oil furnaces. These include two types of primary controls, cad cell and stack-mounted, as well as two types of oil supply systems, one-pipe gravity feed and 2-pipe buried tank. Animated mechanical and electrical schematic diagrams of the simulated oil furnace are provided in real-time. The mechanical diagrams show the flame, fuel flow, and blower rotation. In the electrical ladder diagrams, the controls and switch contacts constantly change state as the furnace operates. The trainee can zoom into the furnace to visually inspect various components, including the electrodes, cad cell, and fan belt, and check for dirty filters, heat exchanger, and flue pipe. Room and ambient temperatures, room thermostat, limit switches, burner air shutter, draft regulator, fuel pump pressure, and electrodes are all adjustable. Room and ambient temperatures, in either Fahrenheit or Celsius, are constantly updated and displayed. Up to 30 commonly encountered 12

15 OIL FURNACE SIMULATOR SIMUOIL Burner Fuel pump Nozzle Combustion chamber Heat exchanger Draft regulator Flue pipe Oil filter Air filter Oil tank valve Primary control Fan motor Burner motor Ignition transformer Control transformer Electrodes Cad cell Pyrostat Safety switch Fan limit switch High-limit switch Centrifugal switch Room thermostat Heat anticipator Motor run capacitor Circuit breaker SIMUOIL provides testing and troubleshooting of the devices listed above, which are commonly found in oil furnaces. mechanical and electrical faults may be selected, as shown in the Fault Lists above. SIMUOIL provides easy-to-use point-and-click selection of meters and test points, which are saved to an Instrument Log to monitor the users troubleshooting skill. Temperatures may be displayed in either Fahrenheit ( F) or Celsius ( C), and pressures may be displayed in either imperial (psig/in. w.c.) or metric (kpa). The on-screen instruments include: Draft gauge Combustion analyzer Fuel gauge Smoke tester Pressure gauge Voltmeter Vacuum gauge Ohmmeter Thermometers Clamp-on ammeter SYSTEM REQUIREMENTS SIMUOIL for Windows requires the following minimum IBM compatible PC computer: Pentium, Core, or equivalent processor (32 or 64-bit) Windows XP, Vista, 7, 8, 8.1, or 10 VGA/SVGA display Hard drive, 18MB available disk space SIMUOIL network version is compatible with Novell and Windows 2000, Server 2003, Server 2008, and Server 2012 FREE DEMO DISK (800) ORDERING INFORMATION SIMUOIL Oil Furnace Simulator Version 5.2 MO-500 Stand-alone computer version, single license $ MO-560 Network version, 25-user (seat) license $1, MO-570 Network version, 50-user (seat) license $2, TO-500 OILINST Instructor Interface, Version 5.1 $ For further prices and ordering information, please see Page 16 13

16 HOT WATER BOILER SIMULATOR SIMUHYDRO SIMUHYDRO simulates a generic gas-fired low-pressure hot water boiler. This residential/light commercial hydronic system uses a cast-iron boiler, a compression tank, and continuous circulation. Room and outdoor temperatures, thermostats, high-limit cut-out, circulator cut-in, gas manifold pressure, cold water pressure, and burner primary air are fully adjustable. The gas and water valves, and compression tank vent may be opened and closed by just a click of the mouse. Having the capability of changing operating temperatures, pressures, and water levels, allows the trainee to observe the boiler system under various conditions; something very difficult to do with real hydronic equipment. SIMUHYDRO provides easy-to-use point-and-click selection of meters and test points, which are saved to an Instrument Log to monitor the users troubleshooting skill. Temperatures may be displayed in either Fahrenheit ( F) or Celsius ( C), and pressures may be displayed in either imperial (psig/in. w.c.) or metric (kpa). The on-screen instruments include: Pressure gauges Ohmmeter Manometer Microammeter Thermometers Clamp-on ammeter Voltmeter Animated mechanical and electrical schematic diagrams of the simulated hot water boiler are provided in real-time. The mechanical diagram shows gas and water flow, water temperatures, boiler and compression tank water levels, and valve positions. In the electrical ladder diagrams, controls and switch contacts constantly change state as the system operates. The trainee may zoom into the system to visually inspect various components, including checking for a dirty combustion chamber, clogged burner and pilot burner orifices, vent damper operation, and proper pilot ignitor position. The trainee can also drain and fill the boiler and compression tank, while observing water levels. 14

17 HOT WATER BOILER SIMULATOR SIMUHYDRO SYSTEM REQUIREMENTS SIMUHYDRO for Windows requires the following minimum IBM compatible PC computer: Pentium, Core, or equivalent processor (32 or 64-bit) Windows XP, Vista, 7, 8, 8.1 or 10 VGA/SVGA display Hard drive, 17MB available disk space Up to 30 commonly encountered mechanical and electrical faults may be selected, as shown in the Fault Lists above. SIMUHYDRO provides testing and troubleshooting of the devices listed below, which are commonly found in hot water boilers. Cast-iron boiler Compression tank Air separator Compression tank vent Backflow preventer Pressure reducing valve Pressure relief valve Pressure gauge Temperature gauge Gas manifold Gas burners Burner orifices Pilot burner Gas shutoff valves Cold water shutoff valve Vent damper Vent pipe Draft hood Diverter fittings Transformer Gas control valve Circulator Heater units Ignition module Circulator motor Vent damper motor Main valve solenoid Pilot valve solenoid Pilot ignitor/sensor Room thermostat Heat anticipator Low water switch (LWCO) High-limit aquastat Blocked vent switch Flame rollout switch Circulator control aquastat Main service switch Circuit breaker SIMUHYDRO network version is compatible with Novell and Windows 2000, Server 2003, Server 2008, and Server 2012 FREE DEMO DISK (800) ORDERING INFORMATION SIMUHYDRO Hot Water Boiler Simulator Version 1.2 MB-500 Stand-alone computer version, single license $ MB-560 Network version, 25-user (seat) license $1, MB-570 Network version, 50-user (seat) license $2, TB-500 HYDROINST Instructor Interface, Version 1.1 $ For further prices and ordering information, please see Page 16 15

18 ORDERING INFORMATION METHODS OF ORDERING MAIL Simutech Systems, Inc. PO Box 7212 Beaverton OR (U.S.A.) PHONE (800) (USA & Canada) (503) Hours: 8:00 am to 5:00 pm Pacific Time FAX (503) ON-LINE STORE / METHODS OF PAYMENT U.S. CUSTOMERS Purchase Order from government agency, school, or corporation (OAC), Net 30-days Visa, MasterCard, or American Express Prepaid by check CANADA & INTERNATIONAL CUSTOMERS Purchase Order from government agency or school, Net 30-days, payable in U.S. funds Visa, MasterCard, or American Express Prepaid by International Bank Check, payable in U.S. funds SHIPPING All orders are shipped FOB shipping point and a shipping charge is added to invoice. Shipment is normally via UPS ground in USA and UPS Air to Canada and international. Next-day or second-day air is available upon request. For Canada and international orders, GST, local taxes, and duty are not included in our prices. Orders are normally shipped within 24-hours from receipt SYSTEM CONTENTS Each simulator system includes the following: CD-ROM User s Manual Instructor s Manual Technical Support, unlimited, with toll-free number (USA and Canada) (1) Additional licenses are required if simulators are installed and used on more than one stand-alone computer at same campus or training facility (2) Network versions are valid for installation on a LAN server at one campus or training facility, for concurrent use by maximum licensed users (3) Network versions for more than 50 users are also available Prices are subject to change without notice Note: Simutech reserves the right to refuse any order, including shipment to countries where prohibited by U.S. export laws or lacking proper international copyright protection. Export, reshipment, or resale is prohibited without prior written permission, subject to U.S. export laws. PRICE LIST MULTIPLE LICENSES FOR STAND-ALONE COMPUTERS PRODUCT 5 LICENSES 10 LICENSES 15 LICENSES 20 LICENSES SIMUAIR TM $1, $1, $1, $2, SIMUPUMP TM 1, , , , SIMUREFR TM 1, , , , SIMUMKT TM 1, , , , SIMUGAS TM 1, , , , SIMUOIL TM 1, , , , SIMUHYDRO TM 1, , , , Prices shown include a single license on one CD-ROM (e.g. "5-Licenses" includes a single license plus 4 additional licenses) Quantity of licenses can not be combined for multiple products For a license quantity not shown, please contact us for a quotation Prices shown are in US Dollars 2015 Simutech Systems, Inc 16

19 SIMUTECH SYSTEMS, Inc. PO Box 7212 Beaverton OR U.S.A. (800) (503) Fax (503)